FloPlast Adjustable Bend 0-90° 110mm Product Code: 14451

Adjustable 0-90°. Polypropylene. Not suitable for solvent welding. Push-fit joint through an innovatively designed seal and snap-cap system. The use of silicone lubricant on all seals will facilitate jointing.


  • 110mm PVCu
  • Ring Seal Joints
  • Suitable for Gravity Drainage & Sewerage
  • Install to Depths of 10m


BBA, EN 12050.
Additional Information
Technical Specification
  • Brand : FloPlast
  • Manufacturing Standards : BBA Certified
  • Product Type : Adjustable Bend
  • Construction Material (Plumbing) : uPVC
  • Total Product Weight : 0.54 kg
  • Model No : D560
  • Connection Type : Push-Fit
  • Pack Size : 1
  • Suitable System : Suitable for Gravity Drainage & Sewerage
  • Product Diameter : 110 mm
  • Pieces in Pack/Case : 1
Product Contents
Delivery & Returns


Standard delivery: €15

Free delivery on all orders over €70.00

Click here to see information on our delivery charges and times



Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.


Click here to see information on returns and cancellation

€13.45 Incl. 20% VAT

Add to Wishlist

FloPlast Adjustable Bend 0-90° 110mm is rated 4.5 out of 5 by 37.
Rated 4 out of 5 by from Excellent in a tight spot This got me out of a tight spot. Being able to adjust the direction when having to move and realign a drain in a confined area was just what was needed.
Date published: 2017-04-20
Rated 4 out of 5 by from Rebuild before use This is a very useful product for joining new drains to old where the angles don't fall nicely to 15, 30, 45 or 90. However I have problems with 2 or the 3 failing the pressure test (air test and a water test too). Using these in future I would do what I had to do with the 2 fails which is take them apart, take the seal off, stuff the seal groove with silicone gel and reassemble. Also tighten the rings as much as possible and tighten more the joint is in final position. I reckon that when moving the joint there is a tendency to undo the rings. And when moving you can introduce grit. Stuffing the seal with gel stops any grit getting in, as does making sure the rings are tightened at the end. Once I had cleaned and stuffed these they passed the pressure test ok. As did one first time. Note you can get this apart in situ without moving the other pipes with a bit of twisting and pushing. You obviously need to clear and area all around to reassembly in situ otherwise you get grit in the gel, but that's let work that digging up a length of drain pipe.
Date published: 2017-04-20
Rated 1 out of 5 by from Infiniely adjustable 110 bend Although this looks a good product, saving you joining 2 or 3 standard 110mm bends together, my experience was not good, i used tis as i had a awkward angle corner to go round, all fitted togeter ok and seal rings were done up tight and tapped home, but afer filling the pipes with water to check for leaks, it was this adjustable bent that failed, Water was leaking from the adjustable seals, so was not impressed as i had to dig it up again and replace it wit 3x 32 degree bens to acheive the same outcome, but these did not leak. SO WILL NOT BUY ONE OF THESE SDJUSTABLE BENDS AGAIN.
Date published: 2016-10-12
Rated 1 out of 5 by from Failed on test I bought 5 of these and after my contractor fitted them they all failed the standard drainage test. They had to be substituted for other fittings. I will be taking them back. The idea is good but needs to go back to R&D
Date published: 2016-08-10
Rated 4 out of 5 by from Adjustable underground bend Just the job for situations where pipe runs are partly installed underground.
Date published: 2016-07-29
Rated 5 out of 5 by from Saves using multiple parts Saves using multiple parts in tight spaces. Also very easy to adjust and not much bigger than standard parts. Worth having one knocking around.
Date published: 2016-07-28
Rated 5 out of 5 by from what a part this was for a job that would of took 3 to 4 parts to get to the same result, what a difference, looks good, will have I always in stock.
Date published: 2016-07-28
Rated 5 out of 5 by from Drainage Whenever I'm putting in any drainage have one of these
Date published: 2016-05-25
  • y_2017, m_8, d_13, h_22
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_37
  • loc_en_GB, sid_14451, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix-ie