Box Spanner Set 8Pcs

Product Code: 4883F
Box Spanner Set 8Pcs
Product Code: 4883F
€12.45
Double-ended box spanners in 16 sizes. Supplied with sliding bar.
€12.45 Incl. 20% VAT
Add to Wishlist

Additional Information
Technical Specification
  • Brand : Unbranded
  • Product Height : 3 cm
  • Product Length : 21.5 cm
  • Total Product Weight : 0.86 kg
  • Product Width : 18.5 cm
  • Pack Size : 1
  • Spanner Product Type : Box
  • Single or Twin Ended : Twin-Ended
  • Pieces in Pack/Case : 8
Product Contents
6-7, 8-9, 10-11, 12-13, 14-15, 16-17, 18-19 and 20-22mm.
Delivery & Returns

DELIVERY

Standard delivery: €15

Free delivery on all orders over €70.00



Click here to see information on our delivery charges and times

 

RETURNS

Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.

 

Click here to see information on returns and cancellation


More Items to Consider

More Items to Consider

Loading... Loading...
1
Box Spanner Set 8Pcs is rated 2.3 out of 5 by 63.
Rated 1 out of 5 by from Poor Design Great idea but why are the bar holes massively inset so that the spanner will not go up over the threaded bar to get to the nut. Totally useless
Date published: 2017-04-12
Rated 2 out of 5 by from Poor design and manufacture A problem I had with these was that the the pressing of the holes for the tommy bar reduced the internal diameter so much that the bolt for the nut I was tightening could not extend past the first set of holes. I notice that other screwfix box spanners did not appear to have this problem. I also found that the the 17mm did not fit a 17mm af nut ( as measured with a vernier caliper.)
Date published: 2017-03-26
Rated 1 out of 5 by from Useless box spanners The whole point of a box spanner is that you can run a nut up a stud. But as the holes for the tommy bar are made by punching in the side of the tube section it is impossible to insert the box spanner over a stud for more than a short distance. I needed to run a nut up a long stud when fixing a kitchen tap and it was no use. Lucky I have a small lathe and I could push a 9mm drill through the box spanner to clear it for the stud. Buy a box spanner with simple holes for the tommy bar, not with punched on holes like these!
Date published: 2017-03-03
Rated 1 out of 5 by from Poorly made product The spanners are cheaply made i had to debur them.
Date published: 2017-02-17
Rated 1 out of 5 by from Terrible design I was under the impression that box spanners would allow threaded bar to go through the centre of the spanner. This design has the cross bar holes punched rather than drilled hence they cause an obstruction, reducing the workable depth to that of a standard socket. I had to force open the internals to do the job in allowing the stud bar to pass through ie butcher a brand new tool. Not impressed!
Date published: 2017-02-15
Rated 5 out of 5 by from Tap spanners Perfect item for job. Had to tighten tap nut up from under the basin. Having large hands struggled to do it with normal spanner due to tight space. Using the spanner in the kit job was done in minuets.
Date published: 2017-01-16
Rated 1 out of 5 by from Not suitable for taps etc The holes in the side of these have been punched through' leaving a very constricted internal diameter which won't fit over any length of threaded rod-making it useless for many jobs. Had to drill out holes to make it usable. In addition, the 17mm wouldn't fit on my 17mm nut, while the 18mm revolved freely on it. Gave up and binned them. To be honest I was very surprised that screwfit sell such a poor quality product.
Date published: 2017-01-15
Rated 1 out of 5 by from Not up to the job Tgese spanners are mainly for tightening mono taps.. the varied sizes are excellent - unfortunately as you can see, the dimple hole about 1 inch down the means you cannot reach the nut as the spigot cannot get beyond the dimple. A plain hole would suffice. Totally useless for the intended job and they do nothing that a standard socket set couldn't do.
Date published: 2017-01-15
  • y_2017, m_5, d_24, h_21
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_63
  • loc_en_GB, sid_4883F, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix-ie