Polytank Cold Water Tank 25gallon (UK) 690 x 515 x 520mm

Product Code: 10500
Polytank Cold Water Tank 25gallon (UK) 690 x 515 x 520mm
Product Code: 10500
€100.95
25 gallon tank with lid. Suitable for new builds and as a replacement tank. Supplied with all fittings stored inside the tank and factory sealed.

Specifications

L x W x H: 690 x 515 x 520mm. Weight: 7.34kg.
€100.95 Incl. 20% VAT
Add to Wishlist

Additional Information
Technical Specification
  • Brand : Polytank
  • Product Height : 520 mm
  • Product Length : 690 mm
  • Product Type : Cold Water Tank
  • Tank Capacity : 25 gallon (UK)
  • Total Product Weight : 7.34 kg
  • Product Width : 515 mm
  • Pack Size : 1
  • Pieces in Pack/Case : 1
Product Contents
Byelaw 30 fittings kit. Part 2 ball valve with float, ball valve, backplate, 22mm compression tank connector, 15mm x ½" angled service valve, plastic support and rubber sealing washer insulation.
Delivery & Returns

DELIVERY

Standard delivery: €15

Free delivery on all orders over €70.00



Click here to see information on our delivery charges and times

 

RETURNS

Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.

 

Click here to see information on returns and cancellation


More Items to Consider

More Items to Consider

Loading... Loading...
1
Polytank Cold Water Tank 25gallon (UK) 690 x 515 x 520mm is rated 4.8 out of 5 by 55.
Rated 5 out of 5 by from A good robust CWF polytank Just managed to squeeze it into the loft after removing the opening surround i.e. check loft opening before buying! This tank is a lot more robust looking than the one it replaced and that had served for over 40 years so this should last forever. It was very easy to install though I had to overcome some difficulties caused by myself. Everything connected well after following the instruction leaflet which has all the details that you need. At the time I wasn't well and very tired and cutting the main water feed without turning off the supply would have been a laugh to watch and you know it's difficult to completely stop a drip from the ball valve water supply elbow when you forget the fibre washer! I used to be competent once, honest.
Date published: 2016-10-21
Rated 5 out of 5 by from Solid tank at a good price A well made tank, much more robust than many of the plastic tanks i have seen. All the fittings included, including the inlet reinforcing required these days, so you are ready to go. The ballcock valve and tank connector appear to be quality made so all in all, it should last a long while before any servicing.
Date published: 2016-10-13
Rated 5 out of 5 by from Great quality product Extremely good quality and easy to install, very robust and well manufacturered.
Date published: 2016-09-16
Rated 5 out of 5 by from Perfect replacement Had to replace an old metal water tank that was seriously rusting. This was a good well made product that fitted the bill perfectly. Don't have to worry now about the old metal tank rupturing and having to replace a ceiling.
Date published: 2016-07-28
Rated 4 out of 5 by from Good Good tank for the money. There was a bit of damage to the seat of the ball valve which meant the service valve would not have sealed up to it but luckily i was using an elbow and olive instead so it didn't matter. Would buy again.
Date published: 2016-05-29
Rated 5 out of 5 by from 25gal cold water tank A good product, easy to install just slightly larger than my original tank so a slight change to the plumbing by using compression elbows and job done.
Date published: 2016-04-10
Rated 5 out of 5 by from Tank A great tank for the prise of it. Very easy to install and of great quality.
Date published: 2015-09-01
Rated 4 out of 5 by from It's just a tank Well what can you say, it's a plastic tank. It comes with all the bits and instructions. In case you don't read them it is worth noting the emphasis on using the correct tools for cutting holes in it. It does seem a bit pricy though. After all it's just a plastic tank with a few bits inside.
Date published: 2015-05-18
  • y_2016, m_12, d_10, h_1
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_55
  • loc_en_GB, sid_10500, prod, sort_[SortEntry(order=AGE, direction=DESCENDING)]
  • clientName_screwfix-ie