Hep2O Push-Fit Flexible Monobloc Tap Connectors 15mm x M10mm x 300mm 2 Pack Product Code: 2043F

€10.45
Push-fit system, no tools required. In4Sure joint recognition lets you know when the pipe is connected. Secure demounting with the HepKey system. Safe for drinking water.

Features

  • 50 Year Manufacturer's Guarantee
  • 50 Year Manufacturer's Guarantee

Specifications

BS 7295.
Additional Information
Technical Specification
  • Brand : Hep2O
  • Product Height : 29 mm
  • Product Length : 300 mm
  • Product Type : Flexible Monobloc Tap Connectors
  • Total Product Weight : 0.32 kg
  • Model No : HD125F/15W
  • Connection Type : Push-Fit
  • Bolt Size : M10
  • Product Depth : 29 mm
  • Pack Size : 2
  • Hose Bore Size : 10 mm
  • Product Diameter : 15 mm
  • Manufacturer Guarantee : 1 Year Guarantee
  • Pieces in Pack/Case : 2
  • Thread Size : M10 "
Product Contents
N/A
Delivery & Returns

DELIVERY

Standard delivery: €15

Free delivery on all orders over €70.00



Click here to see information on our delivery charges and times

 

RETURNS

Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.

 

Click here to see information on returns and cancellation

€10.45 Incl. 20% VAT

Add to Wishlist

1
Hep2O Push-Fit Flexible Monobloc Tap Connectors 15mm x M10mm x 300mm 2 Pack is rated 4.9 out of 5 by 9.
Rated 5 out of 5 by from Great product Great product. Easy to use and connect just push into place and your done would recommend to other people.
Date published: 2017-07-20
Rated 5 out of 5 by from Simple installation Simple to fix in mononbloc tap with the usual reliable hep2o fixing at the other end.
Date published: 2017-02-22
Rated 5 out of 5 by from No Nonsense Reliable Product I bought these to replace the Chinese flexi's that came with the Monobloc basin tap which started to leak 2 weeks after install. I bought the 10mm version as the flow rate is good for a basin. They are an easy fit into the monobloc tap and you have the knowledge that the Hep2O push on will not leak and can be demounted with the key. Good value and I wish I had bought these at the same time as the Monobloc tap.
Date published: 2017-01-28
Rated 5 out of 5 by from Excellent tap connectors Very good quick fit connectors, though you do need special tool to disconnect, but tool cheap and works well.
Date published: 2017-01-02
Rated 5 out of 5 by from Easy to fit and timesaving Very easy to fit. Makes a tricky job of fitting monobloc taps, too often in inaccessible areas much easier. The whole Hep2O range is dependable, you shouldn't hesitate to choose it. It would be great if tap sets actually came with quality fittings like this.
Date published: 2016-12-18
Rated 5 out of 5 by from Hep2o PUSH-FIT FLEXIBLE MONOBL This product is so easy to fit comparing the screwed one i took out, screw one end and push fit the other end as easy job done in less than 5 min.
Date published: 2016-04-22
Rated 5 out of 5 by from Worth the extra Had to fit a monobloc mixer tap in a difficult location (aren't they all!) and I could have used the supplied tails and compression joint them to the Hep2O pipe but it was very cramped so I chose these. SO SO easy to use! I fitted the threaded ends to the tap, installed it and then just pushed the tails onto the waiting Hep2O ends (having fitted inserts to the pipe first of course). The new design of the inserts (knobbly ends) and the new fittings ensured that I was confident that the tails were fitted correctly to the fixed pipe.
Date published: 2015-11-25
Rated 4 out of 5 by from Easy to use Used them on a very deep recessed monobloc kitchen tap, they'd have been better if both had been fitted with the long rigid section that screws into the tap. Luckily they only need a bit of silicone grease on the o rings, then screwing in finger tight - which isn't easy to do by twisting the braided part of the hose - it distorts very easily. The one with the long neck's ok as you can screw it without using the flexible part. Having said that though, they saved time, & didn't leak. I prefer John Guest push fit connectors too, you don't need tools to disconnect them (even though these came with them, they're just something else to lose). Unfortunately John Guest's flexis only have short screw in ends.
Date published: 2015-02-25
  • y_2017, m_8, d_14, h_10
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_9
  • loc_en_GB, sid_2043F, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix-ie