Masonry Mount Black 9mm Pack of 100 Product Code: 68305

Black. Made from ABS.


  • Acid & Erosion Control
  • Insulate Well
  • Not Apt to Age
  • -35°C to 85°C


Made from ABS.
Additional Information
Technical Specification
  • Brand : Unbranded
  • Colour : Black
  • Pack Size : 100
  • Manufacturer Guarantee : 1 Year Guarantee
  • Pieces in Pack/Case : 100
Product Contents
Delivery & Returns


Standard delivery: €15

Free delivery on all orders over €70.00

Click here to see information on our delivery charges and times



Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.


Click here to see information on returns and cancellation

€5.95 Incl. 20% VAT

Add to Wishlist

Masonry Mount Black 9mm Pack of 100 is rated 3.6 out of 5 by 10.
Rated 3 out of 5 by from Needs a 9mm Maronry Drill! This product could be really good, but you try to find a 9mm sds masonry drill. 8mm is too small and you risk the heads snapping off when you hammer them in. 10mm is too big and they fall out. I used an 8mm sds drill and 'waggled it about' to make the hole bigger. Not very accurate, but did the job. So, Screwfix please redesign with either an 8 or 10mm drill in mind!
Date published: 2016-11-03
Rated 5 out of 5 by from 9mm drill required. Like other reviewers, I found these very handy and time saving, but beware. A 9mm drill is the optimum size for holes into masonry. Screwfix do not stock a 9mm SDS drill. I used a SDS 8mm, then opened out with a 9.5mm that I could use in the battery drill. Fixings seem to be solid and are virtually impossible to pull out. Although I did not use all mounts that I bought, I will keep these handy as they can be used with in masonry with cable ties for a wide variety of jobs.
Date published: 2016-03-14
Rated 5 out of 5 by from Great idea Works very well great idea very easy to use I used for hanging temp lights up
Date published: 2015-12-07
Rated 4 out of 5 by from Great for fixing cable runs Used loads of these in brick, cinder and concrete blocks. Agree with other reviewers that drilled hole size needs to be accurate and at 8mm in hard brick or concrete they can be a little tight, careful use of hammer usually gets them in. Only broke heads off a few in several hundreds used, molding design could be improved if the stem between vanes and head was strengthened by lengthwise buttresses to give a '+' cross section. Otherwise a great product for well supported tidy cable runs especially when used for heavier 6mm and 10mm T&E cables.
Date published: 2015-08-04
Rated 5 out of 5 by from They seem to work I've only used a few of these so far but they seem to be working. An 8mm drill gives a hole that is slightly too tight. Tapping the plugs in with a hammer breaks off some of the ribs, but enough are left to hold the plugs tight. I had to remove one and I couldn't shift it, so I had to drill it out.
Date published: 2015-05-27
Rated 4 out of 5 by from Does the job Be good if you stocked a smaller size as well, and stated the drill bit size, as 9mm is the one size that you cannot buy an SDS drill and the 8mm is too tight and 10mm seems to be a little loose? Maybe it was the material I was drilling into?!
Date published: 2015-05-11
Rated 4 out of 5 by from MASONARY FIXINGS We used to use banding to secure items to the underside of the floor beams. Slowly, everyone has been won over to these fixings. Cost effective both in price and labour saving. Have used them on site in the middle of Winter, no problems, as long as you use the correct size drill. We find that an 8mm SDS is ideal.
Date published: 2015-05-06
Rated 4 out of 5 by from Better than expected After reading the only review on these I was a bit put off on getting them but as they were only to use to zip tie outside Xmas lights onto I thought if need be I can drill a slightly bigger hole and use some silicone to help hold it in place, this I did not need to do I tried a 9mm hole first and hit one in with a hammer and it was perfect nice and tight and no problems, I've done around 10 so far and not had any break like suggested in the previous review, so for the price and how useful they are I really can't fault them. The person before me must of been unlucky and had a bad batch is all I can think of.
Date published: 2014-12-12
  • y_2017, m_7, d_23, h_6
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_10
  • loc_en_GB, sid_68305, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix-ie