Towel Radiator Element 150W

Product Code: 73098
Towel Radiator Element 150W
Product Code: 73098
€41.45
Use with plumbed or non-plumbed radiators.

Features

  • Warm, Dry Towels All Year Round
  • Suitable for Oil or Water Systems

Specifications

Can be used with thermo control plate. Must have fused spur protection. BEAB approved EN 60335-1 : 2002; EN 50366 : 2003. BEAB approved EN 60335-1 : 2002; EN 50366 : 2003.
€41.45 Incl. 20% VAT
Add to Wishlist

Additional Information
Technical Specification
  • Brand : Unbranded
  • Product Length : 280 mm
  • Product Type : Towel Radiator Element
  • Power Output (Watts/Kw) : 150 W
  • Total Product Weight : 0.357 kg
  • Pack Size : 1
  • Manufacturer Guarantee : 1 Year Manufacturer's Guarantee
  • Pieces in Pack/Case : 1
Product Contents
Heating element, chrome T-piece and blanking plug.
Delivery & Returns

DELIVERY

Standard delivery: €15

Free delivery on all orders over €70.00



Click here to see information on our delivery charges and times

 

RETURNS

Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.

 

Click here to see information on returns and cancellation


More Items to Consider

More Items to Consider

Loading... Loading...
1
Towel Radiator Element 150W is rated 3.0 out of 5 by 10.
Rated 4 out of 5 by from 150W Towel rad Element Fitted as replacement to oil-filled towel rad. Fitted without problems, full seal achieved without any PTFE and warms up quite quickly. Customer happy straightaway. Can't comment on reliability as only installed last week. It seems obvious but do remember when fitting to oil -filled rad to take rad off wall and turn up-side down so that oil doesn't fall out!!! It stains your fingers as well...
Date published: 2016-02-28
Rated 4 out of 5 by from No issues with this item Bought this for a client. No problems fitting it. Being only 150W it will take longer to heat up, so if you need something to heat up quickly go for a higher watts (400?) or if you what to leave this on for longer it's ideal to save £££.
Date published: 2016-02-02
Rated 1 out of 5 by from do no buy 3 times we tried to fit one of these and all 3 failed - none of them worked and the quality checking on these must be pretty bad for that to happen. Now gone to another manufacturer/seller to try another make!
Date published: 2015-11-27
Rated 5 out of 5 by from Great bit of kit I opted for a 150 watt element to save electricity if it was inadvertantly left on. It has replaced a 400 watt element and performs fantastically. Warms up in 20 mins and dries the towels fine
Date published: 2014-12-16
Rated 1 out of 5 by from Avoid Fitted with new towel rail and failed after 12 hours, replaced without fuss by screwfix and the second one failed again inside 12 hours. 3 fits and travelling expenses along with an unhappy customer makes this product a no no. I would like to say screwfix were very helpful and refunded without any hassle.
Date published: 2014-11-08
Rated 3 out of 5 by from Towel rail150w heating element The Tee-piece was fine, but the element's thread was rough and the burrs needed filing off to enable it to screw freely/fully into place. The o-ring was then able to seal properly. The built-in thermostat seems to be opening 'early' at <60C when fed by a Dimplex controller on max-but ok so far on reduced setting but not as warm as original. Makers Tesla have been informed.
Date published: 2014-09-30
Rated 4 out of 5 by from Simple & straightforward Hard to see how the previous reviewer couldn't get this to seal. It has an 'O' ring which (if it isn't overtightened) should give a reliable seal with no need for any PTFE tape or other sealant. Easy to fit and for me150W gives enough heat in a 500 wide x 1000 tall flat towel rail without running up too big an electricity bill!
Date published: 2014-02-07
Rated 4 out of 5 by from Simple & straightforward Hard to see how the previous reviewer couldn't get this to seal. It has an 'O' ring which (if it isn't overtightened) should give a reliable seal with no need for any PTFE tape or other sealant. Easy to fit and for me150W gives enough heat in a 500 wide x 1000 tall flat towel rail without running up too big an electricity bill!
Date published: 2014-02-07
  • y_2016, m_12, d_5, h_17
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_10
  • loc_en_GB, sid_73098, prod, sort_[SortEntry(order=AGE, direction=DESCENDING)]
  • clientName_screwfix-ie