Yorkshire Tectite Sprint Push-Fit Pipe Elbow 15mm

Product Code: 6486G
Yorkshire Tectite Sprint Push-Fit Pipe Elbow 15mm
Product Code: 6486G
€2.25
Simple, push-fit installation with a tamperproof, slim-line fitting. Guaranteed electrical continuity on copper pipe and high performance 114°C at 10bar.
€2.25 Incl. 20% VAT
Add to Wishlist

Additional Information
Technical Specification
  • Brand : Tectite Sprint
  • Product Length : 35 mm
  • Product Type : Pipe Elbow
  • Total Product Weight : 0.04 kg
  • Product Width : 35 mm
  • Connection Type : Push-Fit
  • Pack Size : 1
  • Product Diameter : 15 mm
  • Manufacturer Guarantee : 1 Year Guarantee
  • Pieces in Pack/Case : 1
Product Contents
N/A
Delivery & Returns

DELIVERY

Standard delivery: €15

Free delivery on all orders over €70.00



Click here to see information on our delivery charges and times

 

RETURNS

Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.

 

Click here to see information on returns and cancellation


More Items to Consider

More Items to Consider

Loading... Loading...
1
Yorkshire Tectite Sprint Push-Fit Pipe Elbow 15mm is rated 4.5 out of 5 by 51.
Rated 5 out of 5 by from V good alternative to solder I recently changed all 6 radiators in my home for double panels. i really wanted to solder the joints but after using copper push fits at work i decided to use them on my central heating at home. There are no specialist tools required to assemble push fits, just invest in a decent pipe cutter and a deburring tool. Note that when you use pipe cutters it debur the outside diameter of the copper pipe. All you have to do is debur the inside of the pipe with a debur tool. i like to finally go over the copper pipe with a steel wool. i then used a clean rag to get rid of any dirt etc. take care to cut pipe straight and trust me you won't have any worries. all joints were solid first time no leaks. if you look inside look inside the push fit you will see a bit of grease intentionally left on the rubber seal in the fitting, this is to aid the pipe sliding over the seal and help prevent gouging the seal as this will cause it to leak. when pushing copper pipe in make sure to push it all the way i believe it goes in just shy of 20mm. there are tools to remove these fittings but I wouldn't! so measure pipe work lengths out properly before assembling! they look great and its a very good alternative to soldering. Hope this helps
Date published: 2017-02-22
Rated 5 out of 5 by from Tectite Push Fittings These fittings are brilliant, they can replace Yorkshire fittings when you have water in the system that you cannot drain completely. Very useful, although they cannot be removed once fitted.
Date published: 2017-01-24
Rated 5 out of 5 by from Used when fitting a radiator Quality fitting, quick and easy to use. Make sure you double check pipe work lengths as you only have one chance. Pipe slide in to fitting 18mm
Date published: 2017-01-10
Rated 5 out of 5 by from Great product Did just what I wanted to do a repair would recomend
Date published: 2016-12-23
Rated 5 out of 5 by from Great for a tight space Only used one when installing an outside tap, but it was great for the last connection in a tight space in the wall cavity where soldering or using a compression joint would have been difficult. A little pricy, but worth it for this job. Pushed straight on with no leaks first time.
Date published: 2016-12-20
Rated 5 out of 5 by from copper pushfit absolutely fantastic item looks beautiful and easy to install far better than the plastic push fit and better than the solder type quick and easy must be the way to go
Date published: 2016-12-07
Rated 5 out of 5 by from Super Simple Fittings I have used lots of these Tectite fittings and they work very well. They look good and a big advantage is that you keep the electrical continuity so that your plumbing can still be bonded which keeps the electricians happy. (using plastic push fit stops this). Two important tips, firstly once put on the pipe they cannot be removed, and second make sure your pipe is clean and cut with a pipe cutter not hacksaw. If the pipe is painted you MUST remove the paint, use wire wool. If the joint leaks simply twist it, then pull and push the fitting and it will seal.
Date published: 2016-12-03
Rated 5 out of 5 by from Good DIY Love these copper push fits. They give a more professional look over plastic and just as easy to fit. Only wish they were a little cheaper. As other reviewers have mentioned that once connected to my knowledge they are unrecoverable.
Date published: 2016-11-26
  • y_2017, m_3, d_21, h_1
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_51
  • loc_en_GB, sid_6486G, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix-ie