H & C Contemporary Bar Valve Fixing Kit Chrome Effect Product Code: 76919

€28.95
Brass construction with chrome effect finish. Suitable for use with bar showers.

Features

  • 2 Year Manufacturer's Guarantee (T&Cs Apply)

Specifications

Model: WP001.
Additional Information
Technical Specification
  • Brand : H and C
  • Product Type : Contemporary Bar Valve Fixing Kit Chrome Effect
  • Model No : WP001
  • Pack Size : 1
  • Manufacturer Guarantee : 2 Year Manufacturer's Guarantee (T&Cs Apply)
  • Pieces in Pack/Case : 1
Product Contents
Faceplate, 2 x adaptors, 2 x brass copper rings, 2 x compression nuts, 2 x SS304 flanges and 2 x screws.
Delivery & Returns

DELIVERY

Standard delivery: €15

Free delivery on all orders over €70.00



Click here to see information on our delivery charges and times

 

RETURNS

Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.

 

Click here to see information on returns and cancellation

Was €34.95

Special Price €28.95

Incl. 20% VAT

Save €6.00 (17%)


Add to Wishlist

More Items to Consider

Loading... Loading...
1
H & C Contemporary Bar Valve Fixing Kit Chrome Effect is rated 4.2 out of 5 by 47.
Rated 5 out of 5 by from Lovely kit Really easy item to use and cost effective. I will definitely be using these more in the future.
Date published: 2018-10-07
Rated 2 out of 5 by from Too short, not fit for purpose Its a great idea and it almost works, however the threaded section that protrudes from the wall is just too short. Its almost like a schoolboy error has been made. The distance from the edge of the nut to the end of the thread is 45mm. The plaster board and skim in my case is 16mm, the tile and adhesive adds another 10mm so we're 26mm down already. This leaves 19mm of thread protruding from the wall which is more than taken up by the 20mm deep pipe concealer. Unless you use a much thinner tile concealer or don't use one at all, it just doesn't work. My advise is look for a similar item with a longer thread as this item is just not fit for purpose and regretfully Im going to have to take it back.
Date published: 2018-09-05
Rated 5 out of 5 by from Great item I use this fitting all the time to install all my exposed showers. Really easy to fit and never had a problem. If it could be 10-20mm longer that would make it even better!
Date published: 2018-07-01
Rated 2 out of 5 by from Not for cavity walls Had to return this as I couldn’t make it work. When attached to a Mira Atom bar shower there’s about 14mm between the shroud and the inlet pipe, so in effect that’s 14mm for board, adhesive and tile, which for me is about 30mm. I can’t really work out in what situation I could make this work
Date published: 2018-05-22
Rated 5 out of 5 by from Can't fit "Mixer" without this After building a 75mm cavity to take a new Shower Mixer Valve and hidden pipe work this "Bar Valve Wall Kit" was then secured to the solid wall in the cavity which then accepted all the pipe work and importantly the weight of the Shower Mixer. Just leave enough thread sticking through to secure your mixer. It can be used either way up depending on the pipework. As I was using waterproof paneling on the front of the cavity, without the Valve Wall Mount being secured inside there is no way the Shower valve would hang on the panel. This was the find of the whole project.
Date published: 2018-04-15
Rated 4 out of 5 by from Great product It is w great product overall- really sturdy if installed correctly. My only issue is the screws are made of cheese- sheared one and rounded the other before I got near the wall. Other than that it’s a great product, easy to fit and level and holds weight well if you’re fitting a heavier shower.
Date published: 2018-03-29
Rated 4 out of 5 by from Easy to fit and works well I used this to replace an inferior fixing kit from Triton for a Triton mixer bar I was fitting. It was easy to fit and being sold brass there was no worry with cross threading the compression joints or doing them up tight enough to seal properly. I wish that I had bought this in the first place instead of going with the manufacturers recommended one.
Date published: 2018-03-06
Rated 2 out of 5 by from Too short! The concept is great, and I would continue to purchase these if the 3/4 tails were longer, but it is not long enough to go through 12mm ply, adhesive and tiles over 5mm thick, and trust me I tried everything I could think of to get it to work. In the end I had to spend £40 on shallow collars! I advise spend the extra money on bristan
Date published: 2018-02-14
  • y_2018, m_10, d_20, h_4
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.8
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_47
  • loc_en_GB, sid_76919, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix-ie