Monument Dry Pressure Test Kit Product Code: 72940

€34.45
Suitable for water, air, gas and petroleum oil pipes up to 60psi and for testing combi systems. Can be left on test while flooring is laid to reveal any nail damage. Tests hot and cold supplies separately to ensure pipes are not crossed. Dry tests pipework during and after installation.

Features

  • Schrader Valve
  • 15mm Push-Fit Fitting
  • Dry Tests Pipework During and After Installation
Additional Information
Technical Specification
  • Brand : Monument Tools
  • Total Product Weight : 0.26 kg
  • Model No : SFX1512 C/W Rubber Boot
  • Pack Size : 1
  • Manufacturer Guarantee : 1 Year Guarantee
  • Pieces in Pack/Case : 1
Product Contents
N/A
Delivery & Returns

DELIVERY

Standard delivery: €15

Free delivery on all orders over €70.00



Click here to see information on our delivery charges and times

 

RETURNS

Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.

 

Click here to see information on returns and cancellation

€34.45 Incl. 20% VAT

Add to Wishlist

More Items to Consider

Loading... Loading...
1
Monument Dry Pressure Test Kit is rated 4.6 out of 5 by 8.
Rated 5 out of 5 by from Well worth the money Just used this item to test new pipework serving 2x bathrooms, heating system & hot water cylinder. Floor tiling has now started in all rooms but system will not be filled with water for at least a week yet! Imagine the potential damage caused by a leaky joint at that stage!! Need to use at least a foot pump, I used a compressor with ease. As a previous reviewer wrote, if you intend to use on a regular basis...insert a short piece of 15mm with a standard push-fit fitting on the end. That way you will wear out the seal in the added fitting & not the tester itself! Great value
Date published: 2014-08-08
Rated 5 out of 5 by from Useful bit of kit Very useful bit of kit for testing pipework before turning the water on. To avoid any problems with the pushfit on it, and to make it easier to use, I fitted a small length of copper pipe into this, then a flexi-pipe, another section of copper, then a pushfit coupler. That way the connector that's being taken on and off pipework each time you use it can be replaced for pennies.
Date published: 2011-12-21
Rated 4 out of 5 by from Great gauge Useful gauge, great for checking during floor laying.
Date published: 2011-06-15
Rated 4 out of 5 by from need to have easy to fit and use,clarify and reliable results. best way to make sure yoursefl all pipeworks made fine
Date published: 2011-03-29
Rated 5 out of 5 by from Very Useful A nice clean easy way of finding out which one of your 136 solder/compression joints is not so great! Get a set of plugs (ref 81203) to go with it and you are sorted. Only gripe would be that for a push fit and a guage it is a bit pricey, though a lot cheaper than the alternative of a mop or a wet ceiling.
Date published: 2009-10-01
Rated 4 out of 5 by from Did the job We brought this guage to progressively check the underfloor heating and all plumbing work during our self build. We used a footpump to test with air before any water was put on. Its been great, as everytime the next section of plumbing has been added, we have tested without water. Result; whole house 100% water tight, except for one joint made by a pro-plumber when the air source heat pump was installed !!! Only downside with this product is that there are no spares available, which means if you damage the seal its a throw away, unless you can winkle the seal out and get something the same size.
Date published: 2009-07-08
Rated 5 out of 5 by from Must Have Great if you need to put floors down before you can wet test, dont use it much but peace of mind when you need it.
Date published: 2009-02-01
Rated 5 out of 5 by from damage saver this is a time and money saving peice of gear ,, no more wet ceilings/floors to repace,after filling ther system..
Date published: 2008-11-28
  • y_2019, m_11, d_12, h_23
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_8
  • loc_en_GB, sid_72940, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix-ie