Stormguard Heavy Duty Around Door Strips Aluminium 1.02m 5 Pack Product Code: 21554

€19.95
1025mm. Around-door draught and rain exclusion. 1-10mm gap seal. Aluminium and nitrile construction.

Features

  • Fits Frames, Windows & Doors
  • Gap Seal: 1-10mm

Specifications

L x W: 1.02m x 25mm. Gap seal: 1-10mm. Fixings Supplied.
Additional Information
Technical Specification
  • Fire Rated (Yes/No) : Non Fire Rated
  • Suitable Locations : Fits Frames, Windows & Doors
  • Brand : Stormguard
  • Product Length : 1.02 m
  • Product Type : Heavy Duty Around Door Strips
  • Fire Rating : Not Fire Rated
  • Fixings Supplied : Fixings Supplied
  • Product Width : 25 mm
  • Colour : Aluminium
  • Pack Size : 5
  • Manufacturer Guarantee : 1 Year Guarantee
  • Pieces in Pack/Case : 5
Product Contents
N/A
Delivery & Returns

DELIVERY

Standard delivery: €15

Free delivery on all orders over €70.00



Click here to see information on our delivery charges and times

 

RETURNS

Hopefully you won't need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.

 

Click here to see information on returns and cancellation

€19.95 Incl. 20% VAT

Add to Wishlist

More Items to Consider

Loading... Loading...
1
Stormguard Heavy Duty Around Door Strips Aluminium 1.02m 5 Pack is rated 4.0 out of 5 by 15.
Rated 5 out of 5 by from Read instructions! Don't steam ahead till you read instructions. Easy to fit but ensure you have correct screw bit size. Gives great draught exclusion.
Date published: 2019-01-28
Rated 5 out of 5 by from easy fit solution to draughts Fitted for a customer to Ill fitting timber door allowing draughts of Oz proportions. 20 mins later the door is wind tight and as an added benefit doesn't rattle in the wind. Excellent performance. Easy to fit, started on the hinge side (the 2 strips with the curved profile) door closed place rubber profile against door, mark screw holes, fit strip with screws loose, measure remaining length for lower section cut aluminium and rubber to same length. swap upper and lower rubbers in aluminium holders so joint in rubber is now staggered to joint in aluminium. mark lower screw holes and fit. With door closed tighten all screws. Repeat on handle side and top. Screw heads are soft so ensure you have correct sized bit and be careful with impact driver. Will use as preferred draught excluder
Date published: 2019-01-25
Rated 5 out of 5 by from Great for older properties I have a few customers with older properties that are pretty draughty. What I like about this product is the fact that it fixes to the outer frame rather than inside the jam or the door itself. The quality metal strips are also adjustable due to the screw holes being elliptical as opposed to just round. The advantage of this is that if the door is a little warped (common on older properties) then you can fine adjust the strips so that the door makes contact along its entire length/width. The fact that the strips are split lengths aid in this too. You get 5 strips in a pack; two per side plus one for the head of the frame. The rubbers on the strips are over long too so that when you join two strips on the frame uprights you just feed the rubber from one strip into the top of the other making a continuous seal. Fitting instructions make fitting look quite complicated but in reality you just need to take your time. Its not rocket science!! I use snips or a hacksaw to create a good join where the horizontal meets the vertical (you don't have to but it just makes for a better seal) and once I have cut the strips to length I just nip the screws up on the frame, close the door and then gently tease into position before tightening fully. You will know if the adjustment is wrong as the door will not close properly. The metal strips are available in either white finish or aluminium with the rubber seal being black. This should satisfy most fitments but you could paint the strips if needed. Finally. If you take your time to fit it properly (1 hour approx.) this product will give a fantastic seal on three sides where the door meets the frame
Date published: 2018-12-16
Rated 5 out of 5 by from When the wild winds blow Our village is in a very windy location and the house gets cold when windy. After using sticky sponge strips which were a waste of time i saw these in a friend's house. Fitted them in about 30 mins. They are adjustable slightly so you aren't in a one shot game. Easily hacksawed to length. Simple effective and easy to use.
Date published: 2018-12-08
Rated 4 out of 5 by from Draught exclusion Good overall quality, the lengths at just over 1meter worried me initially but caused no problems. Easier to fit and transport if anything. Instructions made sense if read somewhere quiet. The joints up the door worked well letting the rubber straddle the 2 aluminium strips to keep them inline. Plenty of screws to do the job. Did’nt take long to fit just over 30mins.
Date published: 2018-08-27
Rated 5 out of 5 by from Stormguard door seal Fitted this today to rear door of my narrowboat. There are 5 strips of 1 metre in length. There are 2 sizes of rubber strips which may caused you a problem. Thankfully my door is around 1.5 meters in height and I did not need all of them. I would recommend you pre drill the holes for the screws. I would recommend this product.
Date published: 2017-11-20
Rated 5 out of 5 by from Have worked very well These are easy to fit & they have made a big difference. I have 5 doors top the eaves of the building in the loft & these have removed the draughts well so far.
Date published: 2017-02-03
Rated 4 out of 5 by from easy to fit good product easy to fit with adjustable screw slots
Date published: 2017-01-20
  • y_2019, m_6, d_18, h_24
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.12
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_15
  • loc_en_GB, sid_21554, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix-ie